nampus
top rider
So after some discussion in this thread:
hqvadventure.com
I came across a KTM abs dongle second hand for half price, so I thought, why not give it a shot.
I found the instructions for the dongle online, basically you should be able to switch functions by having the kill switch in different positions before you turn your key.
The instructions:
Full Street mode (ABS active on the Front and rear Wheel)
Begin with Key in the “off” position.
Engine Stop switch in the “off” position.
Switch Key to the “on” positon.
Move engine stop switch to the “on” position.
Start Motorcycle.
ABS Mode 1 (ABS only active on the front wheel)
Begin with Key in the “off” position.
Engine stop switch in the “on” position.
Switch key to the “on” position.
Start Motorcycle.
ABS Completely off
Start Motorcycle
Hold ABS button down for three plus seconds.
ABS will now be completely turned off.
The dongle plugs into your diagnostics connector which you'll find under the seat unit on the right hand side.
This is the partnumber of the dongle I picked up:

I took of the rubber sleeve and stuffed it behind the battery:

And then it was time for a test ride.
As soon as you switch on the ignition you are greeted with the message: Not Legal on your dash.
Press the mode button and it switches to odo, trip etc, but you are left with the little triangle with exclamation point inside it on the right hand side of the display.
I had switched on the ignition with the killswitch in the on position which should be abs on the front wheel only.
As soon as I started moving both the abs and tc light went out, and a firm jab on the rear brake revealed that the abs on the rear wheel was definitely active.
Switching the bike off, kill switch off, turn the key, kill switch to on, start the bike, same result.
So as far as I could tell, supermoto mode (abs on front wheel only) does not work on the Vitpilen 701.
I then switched off the tc, rode around a little, switched the bike off.
Kill switch in the on position, switched the bike back on.
After I rode off, the abs light went out, tc light stayed on.
So the dongle remembers the setting in which the bike is switched off.

I then turned of the abs, rode a few miles. Switched the bike off, restarted, abs and tc both stayed switched off.
I always switch the bike off by using the key, I don't know what happens when you switch it off using the kill switch. I forgot to try this.
So the dongle does not work as stated in the instructions. But it does remember the tc and abs settings after switching the bike off.
If at any time you want to switch the abs or tc back on, just use the buttons on the dash to do so.
2020 SP 701 ABS
I'm sure this has been discussed ad nauseam, but I'm trying to figure out how to disable ABS on my 2020 SP 701. I've tried holding the unmarked and mode button, as I have seen this online, but no dice. I am able to disable TC just fine. The first service has been done. Thanks!
hqvadventure.com
I came across a KTM abs dongle second hand for half price, so I thought, why not give it a shot.
I found the instructions for the dongle online, basically you should be able to switch functions by having the kill switch in different positions before you turn your key.
The instructions:
Full Street mode (ABS active on the Front and rear Wheel)
Begin with Key in the “off” position.
Engine Stop switch in the “off” position.
Switch Key to the “on” positon.
Move engine stop switch to the “on” position.
Start Motorcycle.
ABS Mode 1 (ABS only active on the front wheel)
Begin with Key in the “off” position.
Engine stop switch in the “on” position.
Switch key to the “on” position.
Start Motorcycle.
ABS Completely off
Start Motorcycle
Hold ABS button down for three plus seconds.
ABS will now be completely turned off.
The dongle plugs into your diagnostics connector which you'll find under the seat unit on the right hand side.
This is the partnumber of the dongle I picked up:

I took of the rubber sleeve and stuffed it behind the battery:

And then it was time for a test ride.
As soon as you switch on the ignition you are greeted with the message: Not Legal on your dash.
Press the mode button and it switches to odo, trip etc, but you are left with the little triangle with exclamation point inside it on the right hand side of the display.
I had switched on the ignition with the killswitch in the on position which should be abs on the front wheel only.
As soon as I started moving both the abs and tc light went out, and a firm jab on the rear brake revealed that the abs on the rear wheel was definitely active.
Switching the bike off, kill switch off, turn the key, kill switch to on, start the bike, same result.
So as far as I could tell, supermoto mode (abs on front wheel only) does not work on the Vitpilen 701.
I then switched off the tc, rode around a little, switched the bike off.
Kill switch in the on position, switched the bike back on.
After I rode off, the abs light went out, tc light stayed on.
So the dongle remembers the setting in which the bike is switched off.

I then turned of the abs, rode a few miles. Switched the bike off, restarted, abs and tc both stayed switched off.
I always switch the bike off by using the key, I don't know what happens when you switch it off using the kill switch. I forgot to try this.
So the dongle does not work as stated in the instructions. But it does remember the tc and abs settings after switching the bike off.
If at any time you want to switch the abs or tc back on, just use the buttons on the dash to do so.
