Vitpilen upper triple clamp

toast449

top rider
Joined
Aug 16, 2023
Messages
328
Location
Lon Gisland NY
Anyone aware of an aftermarket source for the top triple that does not include the clip-on mounts? I'm 6'3", so pretty much all of my weight is on my wrists when I ride. This is fine for shorter trips, but I'd like to switch to Woodcraft clip-ons since they make mounts that can include a variable rise. I would also like the extra length of the Woodcraft bars. Does a Svartpilen stock triple just swap in?
 
Anyone aware of an aftermarket source for the top triple that does not include the clip-on mounts? I'm 6'3", so pretty much all of my weight is on my wrists when I ride. This is fine for shorter trips, but I'd like to switch to Woodcraft clip-ons since they make mounts that can include a variable rise. I would also like the extra length of the Woodcraft bars. Does a Svartpilen stock triple just swap in?

Husqvarna Vitpilen 401 Handlebar Conversion Kit, $319.99.


28602960044_540x392.jpg
 
Right, I don't want to go to bars, just need the triple clamp without the extra ears for the clipons. That kit would say that I can just use the Svart top triple. Not sure how they can sell it that cheap, I looked online and the cheapest I could find the part itself was $160.

X001-Y005.jpg

These are what I'm looking to go to, just give me another 1" of height, allow fine tuning of bar angle for comfort and the hollow bar lets me use motogadget mDisc bar end signals.
 
Right, I don't want to go to bars, just need the triple clamp without the extra ears for the clipons. That kit would say that I can just use the Svart top triple. Not sure how they can sell it that cheap, I looked online and the cheapest I could find the part itself was $160.

View attachment 4516

These are what I'm looking to go to, just give me another 1" of height, allow fine tuning of bar angle for comfort and the hollow bar lets me use motogadget mDisc bar end signals.

$160 for the triple clamp PLUS the cost of the clipons.

I also found it hard to believe, all that stuff for $320. The clutch cable, brake hose, and handlebar controls are probably included because the stock ones aren't long enough.

That begs the question, is the stock cable, hose, and wiring long enough to do what you want to do?
 
Wiring is fine, the brake line might not be but I have a radial master cylinder I will use instead of the stock part so I'll be getting a new line made anyway. I'm just wondering what the top triple part really costs if they can sell all those things together for that price. They are probably getting it for $70 or so. I might reach out and see if they can just sell me the part I need.

I'll start watching ebay for Svart top triples I guess, or if a Vit comes along I could just machine the extra ears off of it in the mill.
 
Wiring is fine, the brake line might not be but I have a radial master cylinder I will use instead of the stock part so I'll be getting a new line made anyway. I'm just wondering what the top triple part really costs if they can sell all those things together for that price. They are probably getting it for $70 or so. I might reach out and see if they can just sell me the part I need.

I'll start watching ebay for Svart top triples I guess, or if a Vit comes along I could just machine the extra ears off of it in the mill.

One guy here drilled and tapped the stock Vit triple clamp.
 
I have another stock vitpilen upper but it seems like you want a svartpilen one. Or like a previous post said,look for a duke 390 upper.
 

Attachments

  • 20230901_181941.jpg
    20230901_181941.jpg
    126.8 KB · Views: 9
Will likely be looking to do this down the road, and for those of you who have done this, do you require a drill press and what are the parts needed. I have powerful hand drills and a tap and die set (not sure I have the size required though) but as I have never felt the need to change my hand position do not know much about the process. Thanks for any thoughts...
 
I need to go with a Svart upper, I can't have the clamps and ears for the stock clipons of the Vit one, they are right where the Woodcraft risers will go. I'll machine the name off, fill the holes with a button for my garage door opener and a usb port and powder coat it black texture. The issue with just jumping to handlebars is they not only give a lot more rise they bring the hands back a couple inches. I want the forward position of the clip ons I just need another inch of height to be more comfortable
 
Exactly that. Those look like 3" risers? I would probably only go 2" to give me about a 1" total lift from stock - this bike is fun but if I'm driving more than 60 miles I'm taking the MT09 so I can be comfortable.

Spent a little time on the lathe today, hate the idea of buying spools when I can just machine them myself...
PXL_20230904_181957158.jpg
 
Back
Top Bottom