Mid muffler / cat delete removed, hesitation with coober

Mark16q

contributing rider
Joined
Oct 11, 2020
Messages
21
Location
Conejo valley
Hello hqv, first post Like this format much more than the other site.

2018 svartpilen and made the mistake of doing all mods at once. So not sure of cause but maybe others have experience.

1. installed comp werkes cat/mid muffler delete
2. installed coober ecu.
3. installed coober air box filter lid.

bike sounds fierce and runs incredibly strong especially higher revs. But if I punch it around 6k it cuts out for a second. I contacted coober and they said I need the mid muffler for it to run right. I’d rather keep the mid muffler off to eliminate weight and add the cat back if that’s what it takes to get rid of the hiccup. Anyone using the coober and with what other mods?

thanks,

Mark
 
You say "it cuts out for a second". Can you describe that in more detail? I mean, that sounds like you are loosing spark for a moment, but I'm not sure you really mean that?
I had heard coober wants the "resonator box" to stay... if that is what they want, maybe start by putting it back and see if that fixes it.... if it does you know exactly what the problem is.
 
I've got coober installed on my RC390 race bike with a high mount werkers exhaust which delete cat and pre-muffler (resonator) and it runs fine for me, the bike feels really good. I'm sure I'm one of the fastest on the straight line thanks to coober
 

Attachments

  • 1604202869992.jpg
    1604202869992.jpg
    78.9 KB · Views: 22
You say "it cuts out for a second". Can you describe that in more detail? I mean, that sounds like you are loosing spark for a moment, but I'm not sure you really mean that?
I had heard coober wants the "resonator box" to stay... if that is what they want, maybe start by putting it back and see if that fixes it.... if it does you know exactly what the problem is.

it feels like a lean condition if I was jetting a carb. It’s more of a bog and coober did say it was going lean. I can’t put just the mid muffler back as the comp werkes deletes both and doesn’t mate with the old parts. Id need to put both cat and muffler back or buy just a cat delete pipe. I’d rather buy just a mid muffler delete to drop the weight even if it doesn’t run as strong. As it is now it is extremely fast in the higher rpm’s and other than the slight bog is a huge improvement. If I roll on throttle slowly it doesn’t bog, just if I snap it open.
 
1. I find that the slip on makes a huge difference in "performance" but little or even negative additional peak horsepower.
2. The expansion chamber does just that, and increases "performance" in certain rpm ranges.

I would also simply imply that the air intake and exhaust "system" need to be tuned to match to make the best power.

Other factors, such as fuel, oil, engine condition, ignition system, etc, will all provide their own subtleties which should not be ignored.
 
Well... for best performance mods like this require one of the following for good performance:

A) you follow a specific "recipe" exactly (airbox - pipe - computer)
B) you spend time on a dyno with an air/fuel chart and adjusting the maps manually.
C) you get a computer device that automatically tunes the bike based on an O2 sensor.

You have to pick what you want to do... either change the bike so it follows a known good recipe, or pick B or C.
The coober is really best only for "A", they told you that. I'd listen to them!
I've done all three of these with various vehicles. They all work. But other methods are just guesswork, IMO.
 
after seeing that ti header and cat delete on another thread here, I ordered them. But could be 2 months until they show up. So for kicks may order the mid muffler delete from comp werkes as it’s pretty cheap and worth the experiment to run with the stock cat. My Grom had an ecu that I could adjust the afr so the limits of ”option a” are a bit frustrating but I’m up for a bit of tinkering to see if I can get what I want and save some weight.
 
Your running with the cat installed, the mid chamber delete and the coober airbox lid installed? (Or do you have the longer comp werkes pipe?)
 
Last edited:
Your running with the cat installed, the mid chamber delete and the coober airbox lid installed? (Or do you have the longer comp werkes pipe?)
Presently have the long comp werks cat/mid muffler delete and coober air box lid. I am going to try the mid muffler delete with stock cat to see how that runs. Just ordered the comp werkes mid muffler delete that I can run with the stock cat. It isn’t exactly what coober recommends but want to try and see if it richens things enough to clear the bog.
 
I was looking at some dyno charts from exaust pipe web sites, they mostly show a huge flat spot between 6 and 7k when the cat is removed with the exception of the very short pipes.

Doesnt the black box do just that, change the effective length of the exhaust?

I am not convinced that what you are experiencing is a coober related issue, it may be an exhaust tuning issue which is just part of the nature of these 373cc bikes?
 
I was looking at some dyno charts from exaust pipe web sites, they mostly show a huge flat spot between 6 and 7k when the cat is removed with the exception of the very short pipes.

Doesnt the black box do just that, change the effective length of the exhaust?

I am not convinced that what you are experiencing is a coober related issue, it may be an exhaust tuning issue which is just part of the nature of these 373cc bikes?
agreed that it isn't caused by coober and was hoping their black box would remedy the lean condition in the 6-7k range. They state it has a map to handle the cat delete but not the mid resonator. The technician I emailed said they hadn't tried with the cat and no resonator, so weren't sure if it could handle it or not so I'll do the experiment. Worst case I'll have some cat and resonator delete's for sale once I'm done with this. My resonator delete is already shipped, so will hook that up with the cat, coober airbox lid and black box and hope it runs smoothly, or at least not as prominent a bog.
 
By black box I was referring to the mid-resonator chamber.

Anyways, with the cat installed I would start with factory lid before trying the coober lid.

You done any gearing?
 
By black box I was referring to the mid-resonator chamber.

Anyways, with the cat installed I would start with factory lid before trying the coober lid.

You done any gearing?
makes sense now that you say it about the black box. Anyways, agree about trying with the lid back on and may even do that now with the cat/black box delete I have on now which might richen it up a bit. No gearing changes. The pull over 7000 is insanely strong now and really hope I can keep that plus get rid of the bog.
 
I think the coober lid and cat delete should typically be done together.

Open exhaust, open air box.
Or
Stock Cat, Stock Lid

And if your regulations allow, and your in the market for a new chain, it might be an opportune time to look into a gearing change which may help put you out of the bog zone for your typical riding speeds.
 
Getting back to this project, put the cat back on and purchased a comp werkes black box eliminator. still have coober ecu and coober air box lid. Did the 15 minute idle ecu reset and took a good ride today. Hesitation without cat is gone. Bike seems torquier and much easier to maintain freeway speeds without watching speedo. Not as intense high rev acceleration but still silly fast to hit redline. I know coober recommends cat removal but the stink on my clothes made work commute unpleasant. no smell on clothes today and think I found a nice compromise. 👍
 
A bit crowded in the garage but you get the idea. Not much to look at but runs well and drops some decent weight too. Barely louder than stock IMO, while without the cat is was pretty loud. I’m running stock plug and 91 fuel, best we have here in SoCal.
 
Back
Top Bottom