2021 Dashboard Disassembly

svarter-every-day

new rider
Joined
Sep 22, 2024
Messages
1
Location
Colorado
Hi folks,

I am trying to disassembly the circular instrument cluster on a 2021 svart. I've been having issues with the backlight flickering and, as time goes on, it just being on in general. At this point, it only turns on for a second when I give the unit a smack.

I took the unit off the bike and removed the clear and rear casings. I am at an impasse though. From what I can tell, the only thing holding the board down now is the wiring harness. Now, accessing that would require me to break the seal around the rubber rectangle and pull it out. I tried doing this, but the glue/epoxy is pretty tough around it and I don't know how deep onto the sides it goes. Using rubbing alcohol seems like a great way to destroy the rubber...

I removed the top component of the electrical and grip tape, but that just exposes the glue-sealed heat-shrink tubing. That kills the thought of pushing the wiring through for more clearance.

My next attempt was wiggling the circuit board whilst holding the back cover. The hope was that there were no screws or clips actually holding the wiring harness to the board. This seemed (and still seems) like the best bet as I was able to get more space. At one point, It did seem like I could go no further. As I don't want to break something and be out $600 for a new dash, I backed off.

I saw, on the thread for changing the polarization, that I could peel off the thin top cover and that there were two screws. That seems unlikely though / more of the way to separate the screen from the board.

Some final comments. I'm about 95% sure that most of the problem comes from the circuit board to wiring connection. I set the unit face down and pushed on the rubber block after trying to wiggle the board out. Figured I'd test it to make sure the thing still worked and bam, the light was on but definitely still having a flicker to it. I'm also worried that it'll slip out after 10 minutes of riding and I'll be back at square one.

If anyone has tips, or has done this before, then I'd appreciate the help!

I'm attaching some photos of where I've gotten to.
dash_back.jpgdash_front.jpgdash_circuit.jpgdash_close.jpg
 
Sounds like vibration induced failure. The chances of finding a visible break seems slim but you probably have little to lose if you need the backlight.

Maybe you can find a cheap non-functional display on flee-bay to take apart as a trial run...

It would be nice to have a 401, 390 and Bajaj 400 to be able to compare electronics. Hard to believe they are too dissimilar. A Duke 390 display would be a nice upgrade.
 
Last edited:
Sounds like a dry joint on the circuit board and i think it would be worth it to get the board removed and all the solder joints resoldered.
I can't help u with removal but many years ago i was upgrading some VERY expensive speakers and the circuit board was stuck down with glue. Obviously the manufacturer didn't want u messing with it but i pried up bit by bit (very carefully) using my fingers and NON metallic items and wolah, the speakers with new drivers/mod board got their upgrade.
 
Last edited:
Hi folks,

I am trying to disassembly the circular instrument cluster on a 2021 svart. I've been having issues with the backlight flickering and, as time goes on, it just being on in general. At this point, it only turns on for a second when I give the unit a smack.

I took the unit off the bike and removed the clear and rear casings. I am at an impasse though. From what I can tell, the only thing holding the board down now is the wiring harness. Now, accessing that would require me to break the seal around the rubber rectangle and pull it out. I tried doing this, but the glue/epoxy is pretty tough around it and I don't know how deep onto the sides it goes. Using rubbing alcohol seems like a great way to destroy the rubber...

I removed the top component of the electrical and grip tape, but that just exposes the glue-sealed heat-shrink tubing. That kills the thought of pushing the wiring through for more clearance.

My next attempt was wiggling the circuit board whilst holding the back cover. The hope was that there were no screws or clips actually holding the wiring harness to the board. This seemed (and still seems) like the best bet as I was able to get more space. At one point, It did seem like I could go no further. As I don't want to break something and be out $600 for a new dash, I backed off.

I saw, on the thread for changing the polarization, that I could peel off the thin top cover and that there were two screws. That seems unlikely though / more of the way to separate the screen from the board.

Some final comments. I'm about 95% sure that most of the problem comes from the circuit board to wiring connection. I set the unit face down and pushed on the rubber block after trying to wiggle the board out. Figured I'd test it to make sure the thing still worked and bam, the light was on but definitely still having a flicker to it. I'm also worried that it'll slip out after 10 minutes of riding and I'll be back at square one.

If anyone has tips, or has done this before, then I'd appreciate the help!

I'm attaching some photos of where I've gotten to.
View attachment 5907View attachment 5908View attachment 5909View attachment 5910
Did you ever manage to dismantle the display? I got as far as you and gave up. My ABS light is dim (then goes out when riding) and I can't work out whether its the ABS module or the LED in the display unit.
 
I answered my own question. I couldn’t see a way of removing the black plastic construction which holds the LCD, nor of separating and removing the PCB. So I worked around this, prizing up the black plastic part sufficient to get a thin nosed soldering iron and tweezers underneath. I then desoldered the faulty SMD yellow ABS LED and stole the yellow LED from the bottom right position, which illuminates an unused function (TC). It’s all working fine now and I’m happy I’ve saved £250 on a second hand replacement display. I really don’t recommend doing this unless you’ve got surface mount soldering experience, jewellers loupes and a very fine soldering iron bit. Hoping nobody else is suffering from failed LEDs.
 

Attachments

  • IMG_8527.jpeg
    IMG_8527.jpeg
    373.9 KB · Views: 10
  • IMG_8526.jpeg
    IMG_8526.jpeg
    460.7 KB · Views: 9
Back
Top Bottom