Search results

  1. fetor56

    OIL IN THE AIR BOX

    five weeks....your more patient than me. After one week i would be looking elsewhere.
  2. fetor56

    New guy with a question

    Black Arrow....in your original post u say "turn signal" Are both doing the same thing or is it just one....if both are doing the same then it can't be a fluke ?
  3. fetor56

    Torque Wrench Preference

    That's a nice set....are u happy with them ?
  4. fetor56

    New guy with a question

    Don't leave it a few days as it's a safety issue. Ring the dealer ASAP and perhaps he can offer suggestions or has heard of this problem before.....personally i haven't. If he knows what's going on the least he can do is make it HIS priority to fix.
  5. fetor56

    New guy with a question

    If your convinced it's not u then contact your dealer immediately is it's important that any traffic knows your intentions . Be seen ,be heard. With my new Vit everything was working fine but he let me bring my bike in at 800 km for it's first service and still retain my warranty. It didn't...
  6. fetor56

    New guy with a question

    Good advice. Make certain it's not u and then progress from there. With anything in life always go from simple to complex solutions..............you'll get there.
  7. fetor56

    New guy with a question

    I'm guessing it's you.
  8. fetor56

    Torque Wrench Preference

    "half or less" .....this is when u get that proverbial trigger pulled.
  9. fetor56

    Quick Release Pressure (NO Wrench Needed Plate)

    I purchased two of these for 2 Makita 18v cordless angle grinders (one for cutting with 1mm blade and the other for grinding and have found them to be invaluable. If the battery goes flat on one grinder simply swap blades to the next. I don't know if your like me and know exactly where...
  10. fetor56

    Baby Bosch Grinder

    Now that i have been using this for numerous jobs (both around the house and on bikes) i have found it invaluable . It's a surprisingly tough little thing, good for tight space or even moderately heavy duty applications. With the guard removed it fits the much cheaper 100mm blades. This would...
  11. fetor56

    Need Help!

    Your doing the RIGHT thing by waiting for more "knowledgeable" 401's than myself to respond and not just going at it like some Lunatic Cowboy. Many people are following this thread and where all here to help. I'm sure soon expert advice will arrive and i know it must be hard but just "hang...
  12. fetor56

    Torque Wrench Preference

    Snap On huh......wanna swap. ;)
  13. fetor56

    Iridium Spark Plug

    As most ppl are probably aware it's a nightmare replacing the OEM plug on a Svrt and Vit. In order to retain my warranty ( for the first service ONLY ) the dealer offered to replace it for the included service price. Even though i like doing my own services it was an offer i couldn't refuse...
  14. fetor56

    EBC Front Sintered Brake Pads FA606HH

    A noticeable improvement over the OEM Brembo sintered (which are good in their own rite anyway) Pathetically east to fit and they really bite (particularly under firm braking) As far as i know these also fit the rear but be a little be careful. Get used to them first, don't just install them and...
  15. fetor56

    Need Help!

    Its not up to us...let's see what Clive Kellen decides to do and hopefully reports back . This would be a good learning curve for all concerned. Tell ya what...Clive will never do that again so that's a positive benefit......no harm no fowl.
  16. fetor56

    Need Help!

    You don't know it's the same...have u ever tested it ?
  17. fetor56

    Need Help!

    I know it's a wet clutch but u don't know how much residual oil is left in the system, so my philosophy is it's easier to add a small amount of oil rather than take out excess oil . No harm can be done.
  18. fetor56

    Can anyone help me figure out what all this melted plastic is?!

    I can't believe Husky would design and test a bike with this MAJOR inherent flaw, particularly when it's been in production with the Svart and Vit for years.....Vandalism perhaps. Says a lot for Husky though , "took a lickin but it's still tickin"
  19. fetor56

    Need Help!

    I would play it safe and drain the oil, no need to remove the cover, simply crack the cover and drain the oil (noting how much oil drains) then refill (as per owners manual) with slightly less oil (1.6 litres instead of 1.7 litres) Start the bike but at least u know the engine is getting...
  20. fetor56

    Need Help!

    To start with i would call as many dealers as u can (not necessarily Husky dealers either) and tell them what your "wife" did....the more info u can gather the better. The minimum i would think is to remove the cover and clean out ALL the oil as thoroughly as possible. It might take also some...
Back
Top Bottom